11/18/2023 0 Comments Cup cabinet pullsSo, you may have to measure if the screw holes are up higher than the bottom of the hardware. As a rule of thumb, I extend that same imaginary line across the bottom rail of the cabinet, and that is where I line up the BOTTOM of the bar pull. If you have wide drawers, you could always use one really long bar pull instead of two smaller bar pulls if you wanted.įor door locations, it can get a little trickier, and that’s where your judgement comes into play. These can be used on both doors and drawers, and while a variety of sizes look great, I love using a longer bar pull (think 5″ or 6″) on upper cabinets because they add some height.įor placement on drawers, I use the same guidelines as we discussed above with cup pulls. If you do want to use knobs on drawers, I usually use two per drawer.īar Pulls: These are arguably my favorite cabinet hardware, because they are sleek, and there are so many fun styles to choose from. Also, I should probably point out that really simple knobs on drawers have been increasing in popularity lately. When we have really small drawers, (think 12″ or under), we may use a knob if a pull doesn’t fit. Then, I center the hole on that line and that’s where I install the hardware.īUT, (yes, you knew there was a but coming), there are times when we will use cabinet knobs on drawers. And as far as placement is concerned, I like to imagine a line that extends across the bottom rail of the cabinet. Knobs: For the most part, we only use knobs on cabinet doors. Sources: Amerock Cup Pull, Amerock Bar Pull Lastly, if you have tall drawers, you can either center them in the overall drawer, or install them on the top rail. As a general rule of thumb, if your drawer is 30″ or wider, I like to use two cup pulls. For really wide drawers, we always recommend using two cup pulls, and then evenly space them. For trash pullouts, I will center the cup pull on the top rail of the door (make sure you center the overall cup pull on the rail, not the screw holes, or else you’ll end up with a cup pull that is too high). The only times I won’t install cup pulls in the center of the drawer slab is if A) it’s a trash pullout, B) you have a really wide drawer or C) you have a really tall drawer. If you have a 5 piece drawer (top and bottom rails, inside panel, and side rails) you want to make sure the hardware itself will fit (centered) in the middle panel before purchasing and installing. So now that you know what types of cabinet hardware there is, the next question is where do you use them?Ĭup Pulls: Cup pulls are only ever used on drawers, and I like to center them in the middle of the drawer slab. Sources: Knob | Bar Pull | Cup Pull | Latch They are usually more substantial because they are used for built–in paneled appliances, so you need something a little more heavy duty. And just as an FYI, if you see the term appliance pull floating around, those are basically larger versions of bar pulls. There are a few other ones, such as concealed pulls, pendants, and specialty knobs, but those aren’t as common, so today we’re focusing on three of the most common types: cup pulls, knobs, and bar pulls. Cup pulls, knobs, pulls (also known as bar pulls), and latches. While there are a plethora of options, most cabinet hardware can be sorted into 4 primary categories. But the perfect cabinet hardware can add SO much personality to your room (we call it the jewelry for cabinets)…so today we hoping to clear up alllll of your questions and simplify the selection process. Plus we share 16 options to shop for your own.Cabinet hardware is a small detail that can cause a lot of headaches because there are SO many options and decisions to make around them. So here’s everything to know about knobs versus pulls, upper cabinets versus lower cabinets, and getting the scale right in your space. Their end goal is really the same-to give you access to the stuff that’s on the other side-but the two options serve a space differently. So let’s begin with the most common hardware on kitchen cupboards: knobs and pulls. “Sizing and function are the two most important factors when considering what cabinet hardware is best,” says Kimberlee Gorsline, founder and principal designer of Kimberlee Marie Interiors. Latches, handles, knobs, or pulls? Matte black, antique brass, or polished nickel? Tiny and seamless or oversize? Understanding the ins and outs of each is the key to making a confident decision. Still, it’s easy to feel overwhelmed by all the choices before you. Picking out kitchen cabinet hardware as your renovation wraps up is like getting the dessert menu at the end of a meal. We may earn revenue from the products available on this page and participate in affiliate programs.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |